Home and property

Slab rates on your electricity bill: why a few extra units cost more

How tiered electricity billing works: why a few extra units can cost more per unit, how to read the tier table on your own bill, and how to check last month's bill.

Editorial illustration for Slab rates on your electricity bill: why a few extra units cost more

In tiered or telescopic electricity billing, the first block of units you use is charged at a lower rate, the next block at a higher rate, and so on. So a few extra units near a boundary are charged at the higher rate, and the bill can jump by more than you expect. The tariff differs by state, utility and consumer category, so use the table printed on your own bill.

How does tiered billing work?

The utility divides your monthly units into bands. Each band has its own rate per unit. You pay the first rate for units in the first band, the second rate for the units that fall in the second band, and so on. The higher rate applies only to units inside that band, in the telescopic method. Some tariffs work differently, so check the explanation on the bill or the utility's tariff order.

What does that look like with numbers?

Suppose, purely as an illustration, the bands are: first 100 units at ₹3 per unit, next 100 at ₹5, and above 200 at ₹7. These rates are made up.

Units usedFirst 100 at ₹3Next 100 at ₹5Above 200 at ₹7Energy charge (₹)
10030000300
2003005000800
220300500140940
3003005007001,500

At 200 units the energy charge is ₹800, which is ₹4.00 per unit on average. At 220 units it is ₹940, so the extra 20 units cost ₹140, or ₹7 each, because they sit in the top band. The average rises to about ₹4.27 per unit (940 divided by 220). Nothing odd happened; those few units were simply charged at the highest band.

How do you read the tier table on your own bill?

  1. Find the section that lists consumption bands or rates per unit. It may be in a small table or on the back of the bill.
  2. Note the band limits and the rate for each, and whether the limits are per month or for the billing period.
  3. Find the units billed for the period, and check that it matches the meter readings printed on the bill.
  4. Look for other lines too: fixed or demand charges, fuel adjustment, duty and surcharge. They are separate from the tier calculation.

How do you check last month's bill?

Put the band limits and rates in a small sheet, and the units used in one cell. The energy charge is the sum of units in each band times its rate. In Google Sheets or Excel, with units in B1, you can write the three-band example as =MIN(B1,100)*3 + MAX(MIN(B1,200)-100,0)*5 + MAX(B1-200,0)*7. For 220 units this returns 300 + 500 + 140, which is 940. Replace the limits and rates with those from your bill. If the result differs from the energy charge printed on your bill, look for a different method, an additional charge, or a billing period of a different length.

Why does your bill jump near a boundary?

Because a heavier month such as a hot summer, or a guest stay, pushes units into the next band. A new air conditioner, a geyser used more often or a few extra weeks at home can add 20 to 40 units without anyone noticing. Looking at the twelve-month pattern of units, not just the amount, shows which month crossed a boundary.

What can you do about it?

  • Check the units, not just the amount, on each bill
  • Note which band you land in each month
  • Switch off standby devices and track whether the units fall
  • Ask the utility to explain any part you cannot reconcile

SpendixAI can total your electricity payments by month once you import statements and put them in a utilities category. The unit counts and bands come from the bill itself, so keep those in your sheet.

SPENDIXAI JOURNAL

Useful ideas start with a clearer picture of your own spending.

Explore your reports