The running cost of a room heater or blower is its wattage times the hours it runs, divided by 1,000 to get units, times the price you pay per unit. For a 1,500 W heater that runs three hours a day at ₹7 a unit, that is ₹31.50 a day. Your wattage, hours and tariff will differ, so use your own.
What is the formula?
- Units (kWh) = watts × hours ÷ 1,000.
- Cost = units × price per unit.
- Monthly cost = daily cost × number of days used.
The wattage is printed on the label or in the manual of the appliance. The price per unit comes from your electricity bill. The simplest honest figure is your bill amount divided by the units consumed, which gives an average cost per unit including fixed charges. If your bill has tiers, the next unit may cost more or less than that average, so look at the bill's tariff lines too.
Worked example: heater, blower and immersion rod
Say the heater is 1,500 W and runs 3 hours a day, the blower is 2,000 W and runs 1 hour, and an immersion rod is 1,500 W and runs half an hour. Assume ₹7 a unit for the sum.
| Appliance | Watts | Hours a day | Units a day | Cost a day at ₹7 |
|---|---|---|---|---|
| Room heater | 1,500 | 3 | 4.5 | ₹31.50 |
| Blower | 2,000 | 1 | 2.0 | ₹14.00 |
| Immersion rod | 1,500 | 0.5 | 0.75 | ₹5.25 |
| Total | All three | 4.5 hours | 7.25 | ₹50.75 |
Check the rows: 1,500 × 3 ÷ 1,000 = 4.5, and 4.5 × 7 = 31.5. Over a 30-day month, ₹50.75 × 30 = ₹1,522.50. That is the most you would add if you used all three every day for the full month at those hours.
Does a thermostat change the answer?
Yes. Many heaters switch their element on and off to hold a temperature, so over an hour they do not draw their full wattage all the time. The calculation above is therefore the upper end for a heater with a thermostat. Your meter will give a better figure than the label.
How do you check it against your meter?
- On a day when you use only the usual appliances, note the meter reading at a fixed time in the morning and again the next morning. The difference is that day's units.
- On another day with similar use plus the heater on for your usual hours, do the same.
- Subtract the first day's units from the second day's. That is what the heater really added.
- Multiply by your price per unit.
Say the normal day showed 9 units and the heater day showed 12.8 units. The heater added 12.8 − 9 = 3.8 units, which at ₹7 is ₹26.60. That is a little under the ₹31.50 from the label, which is what you would expect if a thermostat was cycling. Meters differ, and some are digital with a button to scroll to the reading, so check how yours shows units.
How does this compare with your bill?
Put last winter's bill next to the one from a milder month. The difference is not only the heater, but it is a useful cross-check. If the bill rose by ₹1,300 and your estimate says heating added ₹1,522, either the heater ran less, the thermostat cut in, or other use dropped. The point is that the two numbers should be in the same neighbourhood. If they are far apart, look for something you forgot.
In a spreadsheet, put watts in B2 and hours in C2, the units in D2 as =B2*C2/1000, the tariff in H1 and the cost in E2 as =D2*$H$1. Copy the two formulas down for each appliance. When a sheet stops being enough, SpendixAI can keep your electricity bills in a category by month and show the winter climb in its reports.
Ways to look at the number
- Cost for a single evening, if that is how you use it.
- Cost per month for the full season.
- Cost of one hour, to decide if a shorter run time is enough.
- Difference from last year's winter bill.
Useful ideas start with a clearer picture of your own spending.
Explore your reports


